There is some level of water loss that is to be expected from a swimming pool or a spa in the course of its use. Normal water loss from the structure usually happens in three major ways, that is, through evaporation, splash out, and backwashing the filters. For people who live in hot regions, the amount of water lost to evaporation can be substantial. Here are facts regarding Queen Creek pool service.
Because of the sources of loss of water named above, it is normal to add at least two inches of water to the structure every week. However, had to add more than two inches of water to the structure within a week, it may be a reason to suspect that a leak exists. This is true especially if no reason exists for change in the rate of water loss.
For example, it should be understood that the rate of evaporation may change with the season. Increased usage of the pool in the past few days may lead to an increase in the loss of water from the structure. If the season has not changed and the usage of the structure has remained the same recently yet water loss is happening faster, one should become suspicious.
Nonetheless, before contacting the local structure technician, it is crucial to first confirm the suspicions. A few methods can be employed in detecting the existence of a leak in a pool. To detect the leak, one should start by looking at the obvious. For example, one has to make sure that the leak is not taking place at the pads of various pieces of equipment.
To make sure that the structure does not have a leakage, one should be inspect the filter, pipe valves, pump, and heater. Also, one should check the surrounding ground to make sure it is not wet. One ought to walk around the structure to establish if there is any sunken or eroded surface around the area. If everything is okay, it is then advised to move to the next step of confirmation.
Another method that one can use to determine if their structure is leaking is by marking the level of the water in the structure at the skimmer. This can be done using a pencil, tape, or grease. One should then give the pool a period of 24 hours before coming back to check the new level of the water.
A normal structure should lose a quarter of an inch per day. If the drop in water level is more than a quarter an inch, then it may be indicative of the existence of a leak. One can also use a bucket filled with water to the same level as the level of water inside the structure. The bucket should then be placed on the steps that are used to access the structure.
The bucket should be allowed a duration of 24 hours after which it should be checked. If the water in the pool has dropped in level below that of water in the bucket, then it means that a leak exists. Since water in the bucket and in the pool are bot subjected to evaporation, water loss should happen at the same rate.
Because of the sources of loss of water named above, it is normal to add at least two inches of water to the structure every week. However, had to add more than two inches of water to the structure within a week, it may be a reason to suspect that a leak exists. This is true especially if no reason exists for change in the rate of water loss.
For example, it should be understood that the rate of evaporation may change with the season. Increased usage of the pool in the past few days may lead to an increase in the loss of water from the structure. If the season has not changed and the usage of the structure has remained the same recently yet water loss is happening faster, one should become suspicious.
Nonetheless, before contacting the local structure technician, it is crucial to first confirm the suspicions. A few methods can be employed in detecting the existence of a leak in a pool. To detect the leak, one should start by looking at the obvious. For example, one has to make sure that the leak is not taking place at the pads of various pieces of equipment.
To make sure that the structure does not have a leakage, one should be inspect the filter, pipe valves, pump, and heater. Also, one should check the surrounding ground to make sure it is not wet. One ought to walk around the structure to establish if there is any sunken or eroded surface around the area. If everything is okay, it is then advised to move to the next step of confirmation.
Another method that one can use to determine if their structure is leaking is by marking the level of the water in the structure at the skimmer. This can be done using a pencil, tape, or grease. One should then give the pool a period of 24 hours before coming back to check the new level of the water.
A normal structure should lose a quarter of an inch per day. If the drop in water level is more than a quarter an inch, then it may be indicative of the existence of a leak. One can also use a bucket filled with water to the same level as the level of water inside the structure. The bucket should then be placed on the steps that are used to access the structure.
The bucket should be allowed a duration of 24 hours after which it should be checked. If the water in the pool has dropped in level below that of water in the bucket, then it means that a leak exists. Since water in the bucket and in the pool are bot subjected to evaporation, water loss should happen at the same rate.
About the Author:
Get excellent tips on how to pick a Queen Creek pool service company and more info about a reliable company at http://www.neptunepoolsaz.com right now.
No comments:
Post a Comment